![]()
however if I just browse to 11.22.33.44, then PTCL Modem's configuration page opens up, meaning the external IP is correct and the problem lies in port forwarding. !!Īlso, when I test for port forwarding, I first find out my external IP address through then say my external IP reported on this website is 11.22.33.44, and if the port I want to access is 8765, then I try to browse to 11.22.33.44:8765, but I get nothing. I deleted these port forwarding entries in 'Virtual Servers' and now went to NAT > DMZ Host, and enter my laptop's IP there. I defined two port tables, one for TCP and one for UDP. ![]() I then went to NAT > Virtual Server > Added port forwarding tables, and entered my Laptop's IP address in the Server IP Address's field. Note that there is NO Netgear Router in this configuration anywhere. Once all this is done, the PTCL Modem was at 192.168.1.1 and my laptop was at 192.168.1.2. I then enabled DHCP on the PTCL modem so that it gives an IP to my laptop. :SĬlick to expand.That is exactly what I did (look at post #15 of this thread) ! I connected one laptop directly to the PTCL Modem through an ethernet connection. So how do I configure this in PTCL's modem ? I don't see any Port Forwarding option in the PTCL modem. ![]() I need the PTCL modem to somehow forward this packet to my Netgear router (LAN IP: 10.0.0.1), which can then forward it to my laptop (10.0.0.7). However when I try to browse :8765, nothing happens. In the Port Forwarding I have configured in my Netgear router, I've forwarded all traffic on port 8765 (jDownloader's web interface) to my laptop's local IP, 10.0.0.7. No when I browse this address in my browser, the PTCL modem's webpage opens up. The issue I'm facing is that, I have a DynDNS account, and so suppose that my Dynamic IP is this:. To check your IP settings, go to the command prompt and enter. What you enter here will depend on your IP settings. In the new box, select Use the following IP address. Under the Networking tab, select Internet Protocol Version 4 from the list and click Properties. I already have Port Forwarding configured in my Netgear Wireless router, but I think I also need to configure it in my PTCL modem as well. Right-click Local Area Connection and click Properties. What I'm trying to do is Port Forwarding on the PTCL modem. All my devices (wired and wireless) then connect to my Wireless router, and have IPs like this: 10.0.0.x. Its a different range because this router acts as a DHCP server with its own IP range. This modem then passes off the internet to my Netgear Wireless router whose IP is 10.0.0.1. This modem receives the internet DSL stream, and its IP within my LAN is 192.168.1.254. ![]() Well I recently switched to PTCL's 4 Mbps connection, then I now have their AN1020-16T DSL model. #Securityspy port forwarding modem and router PcSo, I might have setup a port forwarding on 6649 to a local PC 192.168.1.Hi guys. Since they were on the same network, I tried adding the port forwarding form the cable modem to my devices. I had tried putting them on the same network, but that didn't seem to work or I did not have the router's configured correctly. #Securityspy port forwarding modem and router how toNow, I am not sure how to tell the cable modem router, which is supplying my WAN IP, to forward all traffic to my WiFi router then have my WiFi router forward the port request to the specific device. This was easy before, cause I did not have the cable modem router in between. I like the ability to use Remote Desktop to my PCs from outside my network. The gateway is the 192.168.0.1 address to my cable modem router. The cable modem router is on network: 192.168.0.1 and my WiFI router's network is 192.168.11.1. All of devices are connected to my WiFi router and the WiFi router is connected to the cable model router. I still need to use my WiFi router since the signal strength is much better than what my cable modem provider gave me. So, I was able to handle all of my port forwarding via the WiFi router. 0 havoc2k over 2 years ago in reply to WiderMouthOpen. I don't think it does it by IP address but by device/MAC address but I haven't tested. ![]() Then check Network > Advanced Options > Port Forwarding > Add Port Forward. A router with just a single IP address doesn. First, go to and sign in with your admin. They have (at least) one IP for each LAN (well, at least if it's an IP LAN) and usually one (sometimes more, but usually one) address attached to a 'loopback interface' for management purposes. Routers typically have multiple IP addresses. My previous setup was using just a cable modem and my current WiFi router. With port forwarding you can only use the inbound port once. I am not super thrilled about it, but this is what my provider gave me. I recently got a new cable model that also acts as a router. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |